Loading... Please wait...

Sign Up For Special Offers


Assembly Videos

All bikes are delivered 90% built and need assembly of the pedals, seat, handlebars and front wheel, as these are packed for transportation by the manufacturer. The bikes may need some minor adjustment to the brakes and gears but 98% of our bikes dont need any at all. Instructions and a tool are supplied. For your safety, and for legal reasons, we require that you have your bike assembled and adjusted by a trained competent cycle mechanic before use. You must seek professional advice before using the product. As the owner of the product you are solely responsible for the cost of correct assembly and properly maintaining it in a safe operating condition.

PLEASE NOTE: The pedals, crank arms and threads are precision made and are fully tested before they leave the factory. You must put the pedals on the bike correctly. If you are sitting on the bike, then put the right pedal on the right and left pedal on the left hand side. You must put the pedals on by hand until it is impossible to do so any more, but you should be able to turn them 3-4 turns before it gets stiff. Then, fully tighten using a spanner. If you do this incorrectly you will damage the threads and we will not cover this under the warranty.

BikesDirect365 Assembly & Maintenance Instructions 

BikesDirect365 Folding Bicycle Assembly & Maintenance Instructions 


Kingston Bike Assembly


Bike Assembly


BMX Assembly


If you are having any technical difficulties setting up your Raleigh or Diamondback bike you can call the Raleigh/Diamondback technical helpline on 01773 532699 and choose option 3.


DOWNLOAD the Kingston Bicycles bike basket assembly guide

DOWNLOAD the BikesDirect365 Owners Manual


Build guide – Approx 30 minutes 

•  Open carton at the top - take care of staples in top flap. 

•  Remove all parts from the carton - you may need assistance.   

•  First, remove the main section consisting of bike frame, rear wheel, handlebar/stem and front wheel that are tied together. 

•  Then, remove the saddle/seat post and the small box that holds the pedals, reflectors, tools and full owners manual. 

•  If you do not have a work stand place the main section upright on a flat floor so it is resting on the rear wheel and the fork end. 

•  Untie the handlebar/stem section and carefully remove from frame and front wheel. Remove any protective packaging. Turn and twist the handlebar/stem section so cables are at the front and insert stem into head tube. No cables should be to the rear of the bars or twisted or kinked. Ensure the forks are facing forward with the front brake to the front. Tighten to desired height ensuring minimum insertion mark is not visible. Refer to tighten force guides within main manual.

•  For a BMX, you may need to remove stem front or top cap and insert handlebar, reposition stem cap and tighten handlebar into place. You may need to attach the brake cables to the gyro / roto plates (see separate guide with bike).

•  Untie the string holding the front wheel - take care to ensure the crank arm slides out from the spokes smoothly. Remove plastic spacer with fork ends. Loosen axle nuts on wheel and then insert front wheel in fork ends.  Note: You may need to loosen front brake to allow the front wheel past the brake blocks.  Ensure safety washers are located correctly and retighten axle nuts. Readjust front brake by pinching together so block meet rim and retighten cable holding nut/bolt. Refer to tighten force guides within main manual. 

•  If required, fit rear reflector on seat post and then put saddle/post section into frame.  Position into desired position and tighten into place. Ensure minimum insertion mark is not visible. Refer to tighten force guides within main manual. 

•  To fit the pedal needs care and attention. They are labelled "R" (right) and "L" (left). "R" (Right) is the right hand side as you sit on the bike (chain wheel side).  Locate pedal spindle against the hole in the chain wheel crank arm. Turn clockwise by hand to get the tread started. Then, fully tighten using a spanner.  The left side follows the same procedure but this pedal is tightened anti-clockwise. Refer to tighten force guides within main manual. 

•  Fit bell on to handlebar. 

•  Inflate tyres to correct pressure as indicated on tyre sidewall and you are ready to ride.

•  For a BMX, you may need to fit pegs on to the wheel hiub axles by screwing them on. Again, refer to recommended tightening forces in main manual. If not pre-fitted, you will need to fit the chain guard by using the brackets provided.

•  Regular maintenance and checks are important. So, check all nuts and bolts are fully tightened and all parts are functioning correctly before each ride. 

•  We strongly recommend that you have your bike assembled and check before riding by a qualified cycle mechanic. 


Get in touch
Delivery & Postage
Terms & Conditions
Security & Privacy
Returns & Refunds
Bike Assembly Guide
Contact Us
About us
Why Buy From Us
Company Info
Payment Methods:
Cards Accepted
Secure Shopping:
Find us on Google+

All prices are in GBP. Copyright 2019 BikesDirect365. Sitemap